#7543 Water Jet WOVEN INTRLINING

The Mid-Weight Point of the Range

That split matters more than the headline number. The base decides how a fused panel drapes and recovers; the coating supplies the grip. Because only ten grams of glue is doing the bonding, a mid-weight coating, gabardine or poly-cotton shell gains a defined front edge and a collar that stands up, without the panel going flat and boardy under the hand. Fusing happens on the reverse of the shell before assembly, and the garment is built over the fused panel in the usual order.

What the PA/PES Coating Brings

• A blended coating for hard-wearing parts. PA/PES is the film that holds at a cut edge and through repeat washing, which is where a single-component adhesive on a heavier shell can start to lift.
• An even spunlace base. Heat reaches the coating across the whole panel rather than in patches, so a fused front does not develop a soft spot near a hem.
• Clean cutting. The surface is uniform, so blades and dies run at normal speed and stacked layers stay flat between the cut and the press.
• Cut planning without joins.
• Two colours, two jobs. Off-white reads on pale shells and shows a fusing fault at inspection; dyed black stays invisible under dark shells at an open seam.
• One article, several styles. A plant running structured outerwear, workwear and casual jackets can keep press settings per shell rather than per style.

Press Settings and Bond Checks

1. Cut a piece of the actual shell and a matching length of interlining, large enough to cover the whole bond area rather than one corner.
2. Lay the adhesive side against the reverse of the shell — not against the garment lining — and set the press for a polyester base with a PA/PES coating; the shell supplier's temperature and pressure for that face fabric take priority over any general figure.
3. Fuse in a single pass, then leave the panel flat under a weight until it has cooled.
4. Peel an offcut at the cut edge: fibres lifting away with the interlining means the coating has grabbed; a clean separation means temperature or dwell is still short.
5. Wash that offcut the way the finished garment will be laundered, then look for bubbling, edge lift or shrinkage.
6. Log the settings that passed, and re-test only when the shell, its finish or the article changes.

Base, Coating and What It Is Not

The construction is one polyester base and one adhesive layer, with nothing between them. Bond strength comes from the coating; the base decides how the fused panel rolls at a lapel, holds a pocket flap and recovers after a day folded on a shelf. Because the coating is applied evenly along the roll, it activates at a consistent point, which is why lifting at a cut edge stays rare when the press is set correctly.

It bonds to woven shells and to non-woven substrates, and it fuses through light and medium weights without strike-through. On stretch shells, run it with a matching elastic interlining so the fused area keeps its recovery.

One term worth keeping straight on the factory floor: this is a fusible interlining, not a garment lining. A lining covers the inside of the finished piece; this material is fused to the shell beneath it to build the structure that the lining then sits over.

Garments and Panels That Suit 55 gsm

• Structured coats and trench fronts — enough body for a straight front edge and a clean lapel roll on mid-weight coatings and gabardines.
• Tailored jackets — fronts, pocket flaps and vents are fused before the garment lining goes in, so the shape is set before the jacket is bagged out.
• Casual jackets and bombers — a collar stand and a placket without turning a soft cotton shell into a stiff panel.
• Plackets, waistbands and flaps — small parts that need a crisp fold line and have to keep it through pressing and top-stitching.
• Chest logos and appliqué — fused behind the panel, the article works as embroidery backing and stops dense stitching from pulling the cloth out of shape.
• Uniform collars and cuffs — the parts that see the most handling in service.

Workwear, Uniforms and Points of Wear

On a work jacket, collars, cuffs and pocket mouths take more abrasion than any other part of the garment, and they are the first places a light fusible gives up. For a line running one style for weeks, the practical value is repeatability. Base and glue weights are fixed by the article rather than by the batch, so settings recorded against the first container still apply to the fifth, and one roll serves collars, cuffs and waistbands without a change of setup. Colour helps inspection as much as it helps appearance. Off-white shows a fusing fault at a glance; dyed black keeps a dark collar clean at an open seam.

Article 7543 Specification Sheet

Ordering and Stock Availability

Stock available; shipped by the container, so a repeat programme can be planned against a sailing rather than a fresh production run. Off-white and dyed black are both standard and the roll runs 150 cm; a narrower or wider roll is produced as custom water jet interlining to the measurement on your order, with feasibility confirmed before you commit.

Questions about a specific shell, width or panel come back from the people who make the roll. As a water jet interlining factory we can say plainly whether a width is workable and which colour belongs under the fabric you are fusing, instead of answering in generalities.

Scale & Supply Capability

We are a manufacturer rather than a trading company: production, quality control and stock sit under one roof, and we supply buyers worldwide — mostly converters, garment producers and trade partners who resell or specify our interlining into their own programmes. Fast-moving articles are kept in stock, so container-level repeat orders can be released without waiting on a fresh production run. Custom grammage, width and private-label packing are available on request, and we will help you match the right article to your shell fabric before you commit to bulk.

FAQ