#10013 Water Jet WOVEN INTRLINING

Fabric Support and Shape Retention

Article 10013 comes out of our water jet interlining factory as one of the heavier articles in the range: a polyester base carrying a heat-activated PA/PES adhesive. That weight puts it in the shaping band rather than the softening band — the article you specify when a garment part has to hold a defined line instead of simply being stabilised.

As a fusible interlining it is bonded to the reverse of the shell, where it works from the inside. Fronts, stand collars, cuffs and pocket flaps keep their shape through pressing, packing and wear, and because the base is a spunlace web rather than a stiff card-like substrate, the build adds structure without turning a mid-weight shell into a board.

This is an interlining, not a garment lining. A garment lining covers the inside of a finished piece for comfort and a clean interior; an interlining is fused to the shell to create the structure that the lining then sits over. A coat normally uses both, in that order.

The colour pair covers most outerwear shells. Natural off-white sits quietly under pale and mid-tone fabrics; dyed black disappears under navy, charcoal and black. The standard roll is wide enough to lay a full front panel without a join, and the surface is even enough to stack and cut cleanly.

Pattern rooms and production lines handle it the same way: cut to the panel, fuse, then sew. The outcome depends on the press settings rather than on how the roll happens to sit in the stack, which is what makes a heavy shaping article predictable to work with.

- Shape without a board finish — the build sits at the shaping end of the range: substantial enough to hold a structured part, supple enough that the panel still moves with the body after fusing. - Clean cutting — a uniform surface with no thick lanes lets blades and dies run at normal speed, and stacked layers stay flat instead of creeping between the cut and the press. - Wide-format friendly — the standard roll covers a full front panel and suits automatic cutters and fusing machines, so there is less waste at the selvedge and fewer joins in a lay. - Colour that helps inspection — off-white and dyed black give visible contrast against most shells, which makes misalignment and fusing faults easier to catch at the inspection table. - Custom water jet interlining on request — widths and grammages outside the standard build can be discussed with our team so the article fits your panel rather than the other way round.

Technical Composition and Specifications

Production Behaviour and Wash Performance

Fused correctly, this water jet interlining holds its bond through repeated washing and wear. On the line the benefits show up as fewer stoppages. The adhesive activates quickly at normal fusing temperatures, so press time stays short and the panel comes off flat rather than creeping. Shifting between shell and interlining is reduced, which keeps pattern pieces aligned through sewing and cuts the volume of rework a line has to absorb. Repeatability is the other half of it. Base weight and coating weight are fixed by the article, not by the batch, so a programme that passes its first bulk run should pass the tenth. Factories running several styles through one fusing line can hold this article constant and vary only the shell. Finally, the weight is spent where it earns its place. The wearer gets a garment that holds its line and still moves.

Structural Design and Compatibility

The construction is deliberately simple: polyester base, PA/PES adhesive, nothing else. Compatibility is broad. This fusible interlining bonds reliably to woven face fabrics, the usual shells for coats, jackets and workwear, and to non-woven substrates, so a plant running both can keep one article on the shelf instead of two. It also tolerates normal variation in line speed: hold temperature and pressure steady and the adhesive wets out and sets the same way from the first metre of a roll to the last. Uniformity is what protects the yield. There are no thick spots and no thin lanes, so heat reaches the coating evenly and bond strength does not vary across a panel. On large parts, where a single cold patch near a hem is enough to send a coat back through rework, that evenness is the difference between a clean run and a repair pile.

Use Scenarios

• Jacket bodies and yokes — casual and utility jackets that need the chest to stay flat without the panel going rigid across the shoulder. - Stand collars and cuffs — the parts a wearer folds and touches most, and the first place a light interlining gives up. - Pocket flaps, welts and plackets — small, heavily handled pieces where edge curl shows immediately if the bond is weak. - Stretch panels — fused in combination with a matching elastic interlining where the shell has to keep some recovery after bonding. - Pilot runs and sample sets — pattern rooms check hand-feel and shape on a short length before the article is written into a bulk sheet. - Workwear and uniform programmes — where a garment lining is specified for the body, this article goes into the collar, cuff and pocket areas that need structure a lining cannot provide. - Coats and outerwear — the main volume: structured fronts, lapels and stands on wool, wool-blend and heavier synthetic shells. - Fashion outerwear — shaped panels and trims on garments where the silhouette has to read clearly on the rail before anyone tries it on. - High-capacity garment factories — as a water jet interlining factory we supply plants that need the same result from the first roll to the last and cannot absorb variation in the middle of a programme. - Environmental expectations — raw materials are selected with current environmental requirements in mind, which keeps the article usable in programmes where material choice is reviewed.

Reinforcement for Industrial Garment Production

Industrial workwear is where this heavier article earns its keep. Collars, cuffs and pocket mouths on a work jacket take far more abrasion and tension than the equivalent parts on a fashion coat, and a light fusible interlining that reads well in the sample room will soften and collapse long before the garment is worn out. The heavier base is what holds the shape through the wear the end user actually puts on it.

Run it on automatic fusing machines and the result is uniform lamination across the whole lay, not just under the operator's hand. That consistency is what lets a workwear programme keep its appearance standard across sizes and production runs, and it takes the guesswork out of press settings from one shift to the next.

Material utilisation improves as well. The standard roll covers a full front or back panel without a join, and the even surface means fewer pieces are rejected for a poor bond at the edge. On a high-volume workwear line the difference between a good and a marginal interlining shows up as a percentage of the cut, not as a single garment.

Corporatewear and uniform programmes work the same way. The interlining is invisible in the finished piece, but it is the reason a collar stands up on the last jacket of a run the way it did on the first.

Embroidery Backing & Fusing Applications

1. Cut the interlining to the panel or hoop size with a small margin all round, so the backing extends past the area that will be stitched.
2. Lay the adhesive side against the reverse of the shell, smooth the two layers flat and work out any creases before heat is applied.
3. Fuse on a heat press or a continuous fusing machine set for a polyester base with a PA/PES coating, following the settings your machine supplier recommends for the shell in front of you.
4. Let the panel cool flat and unstressed; the bond develops as the adhesive sets, so do not fold or hang the piece while it is still warm.
5. Check the bond on an offcut from the same lay before the batch runs, peeling it once warm and again after washing, and adjust temperature or pressure if an edge lifts.
6. For appliqué and stretch fabrics, back the motif or panel the same way and pair stretch shells with a matching elastic interlining so the fused area can still recover.

Ordering & Delivery

• Stock and shipment — Stock available; shipped by the container, so container-level repeat programmes can be planned against your production calendar.
• Article, colour and width — confirm all three when the order is placed. Other widths across the range can be matched to the quantity you are planning.
• Custom water jet interlining — grammage and width outside the standard build are reviewed case by case: send the specification and the shell you are fusing to, and our team will confirm what is possible.
• Lead time, packing and tracking — confirmed by your sales contact when the order is placed, including the packing method used for container shipment.
• Samples — ask your sales contact about sample availability and the terms that apply.
• Technical questions — as a water jet interlining factory we can advise on which article suits a given shell before you commit to a container.

Scale & Supply Capability

We are a manufacturer rather than a trading company: production, quality control and stock sit under one roof, and we supply buyers worldwide — mostly converters, garment producers and trade partners who resell or specify our interlining into their own programmes. Fast-moving articles are kept in stock, so container-level repeat orders can be released without waiting on a fresh production run. Custom grammage, width and private-label packing are available on request, and we will help you match the right article to your shell fabric before you commit to bulk.

FAQ